F1technical.net

G-raph wrote: ↑

05 Aug 2024, 16:16

LVDH wrote: ↑

30 Jul 2024, 21:04

Also CFD images are out.

I do not understand why the slices are not in the same position for everyone. I have to investigate this.
But you might remember that we did some modifications to the CFD setup before the season as you were concered about tire wake structures. How do you see them now?

Thank you for the CFD pictures. To make it fair, here is my Z-slice from Race 03 :

https://i.postimg.cc/rwfrj1SN/MVRC-2024 ... -1-017.png


I think the tyre wake structures are more realistic with the new settings. The main issue I found is that the front wake is a bit more different than it used to be between the Fast and Standard/Long settings, which adds to the correlation challenge.

yinlad wrote: ↑

13 Aug 2024, 00:21

Would it be possible to confirm if we're going to make any regulation changes for the final two rounds?

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 09:07

Hey guys, in which folder should we submit the fully symmetrical model? every part of the car is in a separate folder, so I'm wondering where should the full assembly be and in which file type?

yinlad wrote: ↑

29 Aug 2024, 09:13

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 09:07

Hey guys, in which folder should we submit the fully symmetrical model? every part of the car is in a separate folder, so I'm wondering where should the full assembly be and in which file type?

You don't submit a full assembly as a single file, only the sub components in their correct folders as described by section '2. Submission Requirements' of the regulations

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 09:45

yinlad wrote: ↑

29 Aug 2024, 09:13

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 09:07

Hey guys, in which folder should we submit the fully symmetrical model? every part of the car is in a separate folder, so I'm wondering where should the full assembly be and in which file type?

You don't submit a full assembly as a single file, only the sub components in their correct folders as described by section '2. Submission Requirements' of the regulations

Ah! i got confused with 2.3 as full car model rather than symmetry of the parts.
Thanks.

BTW do you know what to do when "run the case" isnt working? After completing the "build the case" , when i click on run the case, nothing seems to be happening. RAM or CPU usage is same after clicking it, idk what to do now.

The Rusted One wrote: ↑

29 Aug 2024, 05:40

Hi all, I registered for the challenge a few days ago and have been lurking in here for a while. I'm wondering if it's too late to join for the race this week.

yinlad wrote: ↑

29 Aug 2024, 13:13

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 09:45

yinlad wrote: ↑

29 Aug 2024, 09:13

You don't submit a full assembly as a single file, only the sub components in their correct folders as described by section '2. Submission Requirements' of the regulations

Ah! i got confused with 2.3 as full car model rather than symmetry of the parts.
Thanks.

BTW do you know what to do when "run the case" isnt working? After completing the "build the case" , when i click on run the case, nothing seems to be happening. RAM or CPU usage is same after clicking it, idk what to do now.

You should be able to find the command line that runs behind mflow to get an indication of if something is happening or if it has thrown any errors

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 15:51

yinlad wrote: ↑

29 Aug 2024, 13:13

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 09:45

Ah! i got confused with 2.3 as full car model rather than symmetry of the parts.
Thanks.

BTW do you know what to do when "run the case" isnt working? After completing the "build the case" , when i click on run the case, nothing seems to be happening. RAM or CPU usage is same after clicking it, idk what to do now.

You should be able to find the command line that runs behind mflow to get an indication of if something is happening or if it has thrown any errors

This is what i get after selecting run case for the "Car Coarse" template
"MFlow.py:895: DeprecationWarning: QProcess.startDetached(const QString & command) is deprecated"
what does this mean?

When I select the MVRC, MVRC long, MVRC short nothing seems to be happening. There is nothing happening in the terminal. Final thing is mentioning the ride hide and says "... and done"

Dodgy_Malaka_69 wrote: ↑

30 Aug 2024, 09:03

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 15:51

yinlad wrote: ↑

29 Aug 2024, 13:13

You should be able to find the command line that runs behind mflow to get an indication of if something is happening or if it has thrown any errors

This is what i get after selecting run case for the "Car Coarse" template
"MFlow.py:895: DeprecationWarning: QProcess.startDetached(const QString & command) is deprecated"
what does this mean?

When I select the MVRC, MVRC long, MVRC short nothing seems to be happening. There is nothing happening in the terminal. Final thing is mentioning the ride hide and says "... and done"

yinlad wrote: ↑

30 Aug 2024, 12:08

Dodgy_Malaka_69 wrote: ↑

30 Aug 2024, 09:03

Dodgy_Malaka_69 wrote: ↑

29 Aug 2024, 15:51

This is what i get after selecting run case for the "Car Coarse" template
"MFlow.py:895: DeprecationWarning: QProcess.startDetached(const QString & command) is deprecated"
what does this mean?

When I select the MVRC, MVRC long, MVRC short nothing seems to be happening. There is nothing happening in the terminal. Final thing is mentioning the ride hide and says "... and done"

Ignore Car Coarse, use MVRC short and the process of 'apply settings' -> 'build case' -> 'run case'

variante wrote: ↑

29 Aug 2024, 15:37

The Rusted One wrote: ↑

29 Aug 2024, 05:40

Hi all, I registered for the challenge a few days ago and have been lurking in here for a while. I'm wondering if it's too late to join for the race this week.

Welcome! Yeah, you can join. The deadline is Sunday evening. Just make sure that the organizer (LVDH) notices your entry, so you'll get the link to submit the car.

Hopefully you have a car ready, because there's little remaining time to do anything...