A shameless image thread for the enginephiles

All that has to do with the power train, gearbox, clutch, fuels and lubricants, etc. Generally the mechanical side of Formula One.
johnny comelately
johnny comelately
110
Joined: 10 Apr 2015, 00:55
Location: Australia

Re: A shameless image thread for the enginephiles

Post

bill shoe wrote:
13 Apr 2018, 00:23
johnny comelately wrote:
12 Apr 2018, 20:56
Caterpillar/VW TDI, V10 (90o) cyl, 4 stroke, diesel engine
http://adsves.weebly.com/uploads/2/1/8/ ... 9_orig.jpg
From Wikipedia:
This '4.9' or '5.0' badged V10 TDI diesel engine is only used in Volkswagen Passenger Cars 'premium' models. At its launch in the Volkswagen Phaeton, it became the most powerful diesel-engined car in the world. A heavily modified dry sump version was used in an LMP1 Lola sports car to compete in the 2004 Le Mans under a Caterpillar badge.
Torque and engine speed work out to 369 hp. Probably very difficult to compete at a speed circuit like LeMans with only 369 hp, even back in 2004. But it does meet the now-lost spirit of running street-based engines.
Yes Bill, it looks like an anchor doesnt it. imagine the thoughts of the chassis designer when they said this is your engine

User avatar
flynfrog
Moderator
Joined: 23 Mar 2006, 22:31

Re: A shameless image thread for the enginephiles

Post

flynfrog wrote:
18 Mar 2018, 19:03
Any ideas what the pockets are for between the primary's? Cooling?
Just a little update. These cutouts are just for weight savings. A guy on a facebook group I am on was doing some head work and posted pictures so I asked.

johnny comelately
johnny comelately
110
Joined: 10 Apr 2015, 00:55
Location: Australia

Re: A shameless image thread for the enginephiles

Post

flynfrog wrote:
14 Apr 2018, 03:00
flynfrog wrote:
18 Mar 2018, 19:03
Any ideas what the pockets are for between the primary's? Cooling?
Just a little update. These cutouts are just for weight savings. A guy on a facebook group I am on was doing some head work and posted pictures so I asked.
I cannot see that is the reason, as mentioned before they do not have coolant , so....

User avatar
flynfrog
Moderator
Joined: 23 Mar 2006, 22:31

Re: A shameless image thread for the enginephiles

Post

johnny comelately wrote:
14 Apr 2018, 03:02
flynfrog wrote:
14 Apr 2018, 03:00
flynfrog wrote:
18 Mar 2018, 19:03
Any ideas what the pockets are for between the primary's? Cooling?
Just a little update. These cutouts are just for weight savings. A guy on a facebook group I am on was doing some head work and posted pictures so I asked.
I cannot see that is the reason, as mentioned before they do not have coolant , so....
did you even read my reply to my own quote?

johnny comelately
johnny comelately
110
Joined: 10 Apr 2015, 00:55
Location: Australia

Re: A shameless image thread for the enginephiles

Post

flynfrog wrote:
14 Apr 2018, 03:07
johnny comelately wrote:
14 Apr 2018, 03:02
flynfrog wrote:
14 Apr 2018, 03:00

Just a little update. These cutouts are just for weight savings. A guy on a facebook group I am on was doing some head work and posted pictures so I asked.
I cannot see that is the reason, as mentioned before they do not have coolant , so....
did you even read my reply to my own quote?
That response is needlessly rude and disrespectful, of course I did.
if you look back, I posted this before.
I was simply trying to make whoever aware of that instead of only considering "weight saving" which doesnt add up in my opinion.

User avatar
djos
113
Joined: 19 May 2006, 06:09
Location: Melbourne, Australia

Re: A shameless image thread for the enginephiles

Post

johnny comelately wrote:
14 Apr 2018, 03:27
I was simply trying to make whoever aware of that instead of only considering "weight saving" which doesnt add up in my opinion.
It's pretty darn obvious what they are for, there's no other practical purpose for them ... you know occam's razor and all that.
"In downforce we trust"

User avatar
flynfrog
Moderator
Joined: 23 Mar 2006, 22:31

Re: A shameless image thread for the enginephiles

Post

He said I could repost his pictures and he sent me one of some of the other weight savings cutouts. Since there is no worry about cutting into a water jacket they can cut some weight out. They are around 22" long and weigh a decent amount.

Image

Image

Image

Maritimer
Maritimer
19
Joined: 06 Sep 2017, 21:45
Location: Canada

Re: A shameless image thread for the enginephiles

Post

Are we really still stuck on this :lol:

J.A.W.
J.A.W.
109
Joined: 01 Sep 2014, 05:10
Location: Altair IV.

Re: A shameless image thread for the enginephiles

Post

Interesting, ta for that, ff.

Looks as if those 'ports' could allow cooler ambient air - to flow into/around the valve gear, too?

Very little lube used, or likely needed for a quick burst of power, or surely it'd spray out..
..or is there a device attached via those threaded drillings at either end, too?
"Well, we knocked the bastard off!"

Ed Hilary on being 1st to top Mt Everest,
(& 1st to do a surface traverse across Antarctica,
in good Kiwi style - riding a Massey Ferguson farm
tractor - with a few extemporised mod's to hack the task).

noice
noice
1
Joined: 15 Apr 2018, 06:01

Re: A shameless image thread for the enginephiles

Post

Except for the fact that those ports are covered by the exhaust header flange.

Brad Anderson Enterprises (BAE) even puts these holes on the intake side as well.Image


Noonan Race Engines X1 heads (Top Alcohol) puts them on their heads.
Image

As you can see from the lower left side, there is no cooling in their blocks.
Image

NRE doesn't run the different bolt pattern on all of their heads, since they are alcohol only heads they probably don't see the need for the extra exhaust header fasteners
Image

Alan Johnson Performance Engineering (AJPE) has come up with a new exhaust header bolt pattern that is supposed to be better.
Image

Nitro engines don't even use valve seals as they don't need them.

johnny comelately
johnny comelately
110
Joined: 10 Apr 2015, 00:55
Location: Australia

Re: A shameless image thread for the enginephiles

Post

I have just got home to find all this.....
This is our head which I have designed, drawn, had simulated and started machining today.
It is for alcohol and some nitro, it is non-coolant, it is powerful.
We know exactly what every nook and cranny is there for.
Thank you JAW for stating the obvious and there is another reason the cavity is used for.
Weight saving is a handy by-product when they can weigh 40 kg (ours does not)
If there is anything I could wish for is a more courteous, professional culture which thankfully is practiced by some, but there is an element that does not.
Image

User avatar
MrPotatoHead
53
Joined: 20 Apr 2017, 19:03
Location: All over.

Re: A shameless image thread for the enginephiles

Post

As mentioned by the gentleman above the primary reason for those pockets is not weight saving.
It might be a handy by product but it is not why they are there.
If it was purely for weight saving the entire exhaust face would be very different wand rather than pockets the flange contact areas would be islands.

Some of the pockets are very complex in shape, often having an undercut that requires 5-Axis machining.

bill shoe
bill shoe
151
Joined: 19 Nov 2008, 08:18
Location: Dallas, Texas, USA

Re: A shameless image thread for the enginephiles

Post

I don't know why the pockets are there but I'll throw out a guess that they exist to control stiffness and therefore keep head strength and stiffness high in the places where it's most needed. Or maybe to control dynamic distortion under huge combustion pressures, this is sorta the same thing as my first guess.

63l8qrrfy6
63l8qrrfy6
368
Joined: 17 Feb 2016, 21:36

Re: A shameless image thread for the enginephiles

Post

johnny comelately wrote:
15 Apr 2018, 11:19
I have just got home to find all this.....
This is our head which I have designed, drawn, had simulated and started machining today.
8/f/2018/105/1/e/img_6204a_by_sherlockedshock-dc8vhtr.jpg[/url]
Not offence, but please do not take credit for someone else's work.
Someone that asks "how are cranks made" and "how do design a nut that doesn't come loose" can't design a cylinder head.

It really isn't my intention to be rude however I have to point out that you are exaggerating your contribution.

User avatar
flynfrog
Moderator
Joined: 23 Mar 2006, 22:31

Re: A shameless image thread for the enginephiles

Post

J.A.W. wrote:
15 Apr 2018, 05:29
Interesting, ta for that, ff.

Looks as if those 'ports' could allow cooler ambient air - to flow into/around the valve gear, too?

Very little lube used, or likely needed for a quick burst of power, or surely it'd spray out..
..or is there a device attached via those threaded drillings at either end, too?
not sure what threads you are talking about J.A.W. the threads next to the this valve are for fuel injectors.
Image

I would think if they wanted them for cooling they would be finned. There just isn't much surface area there compared to the waste heat of a top fuel engine to radiate heat into the air especially since that air is between two glowing hot primaries.